 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Pressure Freescale Semiconductor Media Resistant Integrated Silicon Pressure Sensor for Measuring Absolute Pressure, On-Chip Signal Conditioned, Temperature Compensated and Calibrated The MPXHZ6117A series pressure sensor integrates on-chip, bipolar op amp circuitry and thin film resistor networks to provide a high output signal and temperature compensation. The sensor's packaging has been designed to provide resistance to high humidity conditions as well as common automotive media. The small form factor and high reliability of on-chip integration make this sensor a logical and economical choice for the system designer. The MPXHZ6117A series piezoresistive transducer is a state-of-the-art, monolithic, signal conditioned, silicon pressure sensor. This sensor combines advanced micromachining techniques, thin film metallization, and bipolar semiconductor processing to provide an accurate, high level analog output signal that is proportional to applied pressure. MPXHZ6117A Rev 0, 03/2010 MPXHZ6117A Series 10 to 115 kPa (14.5 to 16.7 psi) 0.4 to 4.653 V Output Features * * * * * * Resistant to High Humidity and Common Automotive Media Improved Accuracy at High Temperature 1.5% Maximum Error over 0C to 85C Temperature Compensated from -40C to +125C Durable Thermoplastic (PPS) Surface Mount Package (SSOP) with Optional Axial Port Ideally Suited for Microprocessor or Microcontroller Based Systems ORDERING INFORMATION # of Ports Package Case Device Name Options No. None Single Dual Super Small Outline Package (Media Resistant Gel) (MPXHZ6117A Series) MPXHZ6117A6U MPXHZ6117A6T1 MPXHZ6117AC6U MPXHZ6117AC6T1 Rail Tape & Reel Rail Tape & Reel 1317 1317 1317A 1317A Gauge Pressure Type Differential Absolute Device Marking * * * * * * * * MPXHZ6117A MPXHZ6117A MPXHZ6117A MPXHZ6117A SUPER SMALL OUTLINE PACKAGE MPXHX6117A6U/6T1 CASE 1317 MPXHX6117AC6U/6T1 CASE 1317A (c) Freescale Semiconductor, Inc., 2010. All rights reserved. Pressure Operating Characteristics Table 1. Operating Characteristics (VS = 5.0 VDC, TA = 25C unless otherwise noted, Decoupling circuit shown in Figure 3 required to meet electrical specifications.) Characteristic Pressure Range Supply Voltage(1) Supply Current Minimum Pressure @ VS = 5.0 V Full Scale Output(2) @ VS = 5.0 V Full Scale Output(3) Sensitivity Offset Stability(4) (0C to 85C) (0C to 85C) Symbol POP VS IS VOFF VFSO Min 10 4.75 -- 0.340 Typ -- 5.0 6.0 0.4 Max 115 5.25 10 0.461 Units kPa Vdc mAdc Vdc (0C to 85C) 4.592 4.653 4.714 Vdc (0C to 85C) VFSS V/P -- -- -- -1.5 4.253 40.5 -- -- -- 1.5 V mV/kPa %VFSS 1. Device is ratiometric within this specified excitation range. 2. Offset (VOFF) is defined as the output voltage at the minimum rated pressure. 3. Full Scale Span (VFSS) is defined as the algebraic difference between the output voltage at full rated pressure and the output voltage at the minimum related pressure. 4. Accuracy (error budget) is the deviation in actual output from nominal output over the entire pressure range and temperature range as a percent of VSS span at 25C due to all sources of error including the following: Linearity: Output deviation from a straight line relationship with pressure over the specified pressure range. Temperature Hysteresis: Output deviation at any temperature within the operating temperature range, after the temperature is cycled to and from the minimum or maximum operating temperature points, with zero differential pressure applied. Pressure Hysteresis: Output deviation at any pressure within the specified range, when this pressure is cycled to and from minimum or maximum rated pressure at 25C. Offset Stability: Output deviation, after 1000 temperature cycles, -40 to 125C, and 1.5 million pressure cycles, with minimum rated pressure applied. TcSpan: Output deviation over the temperature range of 0 to 85C, relative to 25C. TcOffset: Output deviation with minimum pressure applied, over the temperature range of 0 to 85C, relative to 25C. MPXHZ6117A Preliminary 2 Sensors Freescale Semiconductor Pressure Maximum Ratings Table 2. Maximum Ratings(1) Rating Maximum Pressure (P1 > P2) Storage Temperature Operating Temperature Output Source Current @ Full Scale Output(2) Output Sink Current @ Minimum Pressure Offset Symbol PMAX TSTG TA IO + IO Value 400 -40 to +125 -40 to +125 +0.5 -0.5 Unit kPa C C mAdc mAdc 1. Exposure beyond the specified limits may cause permanent damage or degradation to the device. 2. Maximum Output Current is controlled by effective impedance from VOUT to GND or VOUT to VS in the application circuit. Figure 1 shows a block diagram of the internal circuitry integrated on a pressure sensor chip. VS 2 Sensing Element Thin Film Temperature Compensation and Gain Stage #1 3 GND Gain Stage #2 and Ground Reference Shift Circuitry 1 VOUT Pins 1, 5, 6, 7, and 8 are NO CONNECTS for super small outline package devices. Figure 1. Fully Integrated Pressure Sensor Schematic MPXHZ6117A Sensors Freescale Semiconductor Preliminary 3 Pressure ON-CHIP TEMPERATURE COMPENSATION AND CALIBRATION The performance over temperature is achieved by integrating the shear-stress strain gauge, temperature compensation, calibration, and signal conditioning circuitry onto a single monolithic chip. Figure 2 illustrates the configuration in the basic chip carrier (case 1317-04) prior to porting. A gel die coat isolates the die surface and wire bonds from the environment, while allowing the pressure signal to be transmitted to the sensor diaphragm. The gel die coat and durable thermoplastic package provide a media resistant barrier that allows the sensor to operate reliably in high humidity conditions as well as common automotive media. NOTE: The MPXHZ6117A series pressure sensor's operating characteristics, internal reliability and qualification tests are based on use of air as the pressure media. Media, other than air, may have adverse effects on sensor performance and long-term reliability. Contact the factory for information regarding media compatibility in your application. Figure 3 shows the recommended decoupling circuit for interfacing the integrated sensor to the A/D input of a microprocessor or microcontroller. Proper decoupling of the power supply is recommended. Figure 4 shows the sensor output signal relative to pressure input. Typical, minimum, and maximum output curves are shown for operation over a temperature range of 0 to 85C using the decoupling circuit shown (Figure 3). The output will saturate outside of the specified pressure range. Fluorosilicone Gel Die Coat Wire Bond Die P1 Stainless Steel Cap +5.1 V Thermoplastic Case Lead Frame Absolute Element Sealed Vacuum Reference Die Bond VS Pin 2 100 nF MPXHZ6117A VOUT Pin 4 GND Pin 3 47 pF To ADC 51 K Figure 2. Cross Sectional Diagram SSOP (not to scale) Figure 3. Typical Application Circuit (output source current operation) 5.0 4.5 3.5 Output (Volts) 3.0 2.5 2.0 1.5 1.0 0.5 Transfer Function: Vout = Vs*[(0.0081*P-0.00095) 1.5*0.0081*VS*Tm] 4.0 VS = 5.0 V 0.25 Vdc, Temp. = 0 to 85C MAX TYP MIN 0 5 15 25 35 45 55 65 75 Pressure in kPa 85 95 105 115 125 Figure 4. Output vs. Absolute Pressure MPXHZ6117A Preliminary 4 Sensors Freescale Semiconductor Pressure Temperature Error Band MPXHZ6117A Series 4.0 3.0 Temperature Error Factor 2.0 1.0 0.0 -40 -20 0 20 40 60 80 100 120 140 Temperature in C NOTE: The Temperature Multiplier is a linear response from 0C to -40C and from 85C to 125C. Temp -40 0 to 85 125 Break Points Multiplier 3 1 1.75 Pressure Error Band 3.0 2.0 Pressure Error (kPa) 1.0 0.0 -1.0 -2.0 -3.0 Pressure 10 to 115 (kPa) Error (Max) 1.5 (kPa) 20 40 60 80 100 120 Pressure (in kPa) Error Limits for Pressure SURFACE MOUNTING INFORMATION Minimum Recommended Footprint for Super Small Outline Packages Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor package must be the correct size to ensure proper solder connection interface between the board and the package. With the correct pad geometry, the packages will self-align when subjected to a solder reflow process. It is always recommended to fabricate boards with a solder mask layer to avoid bridging and/or shorting between solder pads, especially on tight tolerances and/or tight layouts. 0.050 1.27 TYP 0.150 3.81 0.387 9.83 0.027 TYP 8X 0.69 0.053 TYP 8X 1.35 inch mm Figure 5. SSOP Footprint (Case 1317 and 1317A) MPXHZ6117A Sensors Freescale Semiconductor Preliminary 5 Pressure PACKAGE DIMENSIONS PAGE 1 OF 3 CASE 1317-04 ISSUE F SUPER SMALL OUTLINE PACKAGE MPXHZ6117A Preliminary 6 Sensors Freescale Semiconductor Pressure PACKAGE DIMENSIONS PAGE 2 OF 3 CASE 1317-04 ISSUE F SUPER SMALL OUTLINE PACKAGE MPXHZ6117A Sensors Freescale Semiconductor Preliminary 7 Pressure PACKAGE DIMENSIONS PAGE 3 OF 3 CASE 1317-04 ISSUE F SUPER SMALL OUTLINE PACKAGE MPXHZ6117A Preliminary 8 Sensors Freescale Semiconductor Pressure PACKAGE DIMENSIONS PAGE 1 OF 2 CASE 1317A-04 ISSUE D SUPER SMALL OUTLINE PACKAGE MPXHZ6117A Sensors Freescale Semiconductor Preliminary 9 Pressure PACKAGE DIMENSIONS PAGE 2 OF 2 CASE 1317A-04 ISSUE D SUPER SMALL OUTLINE PACKAGE MPXHZ6117A Preliminary 10 Sensors Freescale Semiconductor How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor China Ltd. Exchange Building 23F No. 118 Jianguo Road Chaoyang District Beijing 100022 China +86 010 5879 8000 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center 1-800-441-2447 or +1-303-675-2140 Fax: +1-303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals", must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. All other product or service names are the property of their respective owners. (c) Freescale Semiconductor, Inc. 2010. All rights reserved. MPXHZ6117A Rev. 0 03/2010 |
Price & Availability of MPXHZ6117AC6T1
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |